Item Name: Item Gone: FS Piston Skull Carvings - Desk Ornaments - Man Cave Displays
Location: Richmond Hill
Zip Code: 31324
Item is for: Sale Only
Sale Price: 65
Willing to Ship: Yes
Bill of Sale Required?: No
Item Description: Below is what I currently have available and turnaround is usually less than three days if I don't have it. Now for the fun part: PRICING -
$65 full faced pistons with/without cigar.
$35 half faced with upper jaw only.
Shipping is normally around $11 inside of Georgia.
I try to keep my hands busy and the extra allowance pays for shooting hobbies (and out of trouble with my wife). Located in Richmond Hill, GA (south Savannah). Background: I cut these from real pistons and currently have a stash of new Wiseco's that I'm using. Been fortunate to have my work recognized that others have sent me theirs (from a blown engine or maybe it was sentimental) to do the work on. As long as there's enough area to make something, I'll cut it. Done everything from outboard engine pistons, lawnmower, 4 cylinder auto to Cummins diesel. -If you're on FB, check out my page and search ---> PISTON SKULLS - HANDCRAFTED <---
Goal - keep my hands busy, while not over charging. Compare real pistons on ebay and other sites for similar work. Ebay has a lot of 3D printed stuff.
These are regular auto pistons so the diameter is 4" and they range in height from 2.5 to 3.25 for the biggest. I may even have the wrist pin for them too. Let me know if you want more photos.
Jay (West Key on FB)
Here's the link to my page. I'm not looking for a bunch of followers or BS like that. I want to sell you a piston and make it into something you'll be proud to show off.
www.facebook.com
Pictures:









Location: Richmond Hill
Zip Code: 31324
Item is for: Sale Only
Sale Price: 65
Willing to Ship: Yes
Bill of Sale Required?: No
Item Description: Below is what I currently have available and turnaround is usually less than three days if I don't have it. Now for the fun part: PRICING -
$65 full faced pistons with/without cigar.
$35 half faced with upper jaw only.
Shipping is normally around $11 inside of Georgia.
I try to keep my hands busy and the extra allowance pays for shooting hobbies (and out of trouble with my wife). Located in Richmond Hill, GA (south Savannah). Background: I cut these from real pistons and currently have a stash of new Wiseco's that I'm using. Been fortunate to have my work recognized that others have sent me theirs (from a blown engine or maybe it was sentimental) to do the work on. As long as there's enough area to make something, I'll cut it. Done everything from outboard engine pistons, lawnmower, 4 cylinder auto to Cummins diesel. -If you're on FB, check out my page and search ---> PISTON SKULLS - HANDCRAFTED <---
Goal - keep my hands busy, while not over charging. Compare real pistons on ebay and other sites for similar work. Ebay has a lot of 3D printed stuff.
These are regular auto pistons so the diameter is 4" and they range in height from 2.5 to 3.25 for the biggest. I may even have the wrist pin for them too. Let me know if you want more photos.
Jay (West Key on FB)
Here's the link to my page. I'm not looking for a bunch of followers or BS like that. I want to sell you a piston and make it into something you'll be proud to show off.
Piston Skulls - Handcrafted | Richmond Hill GA
Piston Skulls - Handcrafted, Richmond Hill. 76 likes · 110 talking about this. Keeping my mind and hands busy is also good for my spirit. Prices start at $65 for most all you see on this page.
Pictures:









DISCLAIMER: Always comply with local, state, federal, and international law. The Outdoors Trader does not become involved in transactions between parties. Review our
Privacy Policy
and
Terms of Use
for more information.


