***To trade for this item you will need a minimum of 10 positive feedbacks or have been on the odt for 5 years or more with some level of positive feedback. If you have multiple negative feedbacks I won’t trade with you***
This is very close to new. I’ve only fired around 100 rounds out of it. I did every upgrade that I could think of that would enhance the platform. You have to buy the entire kit. The only parts I’ll sell separately would be the additional triggers or the OEM barrel/recoil rod assembly. All of the parts, mags, and accessories are close to brand new. The only exception to that would be the ripstick and the chassis smoothing that performed. The Ripstick front sight was slightly scuffed during install so I touched it up with some enamel paint. The frame around the trigger well had a raised seam of plastic which I found uncomfortable. I sanded down just the surface and edges to an 800 grit surface just to remove this seam and smooth the sharp edges. It’s much more pleasurable to shoot. I checked with Flux before sanding/smoothing down the seam and sharp edges and they assured me it was fine to do so. See the below parts list and my trade list below. This is from my personal collection. I’m losing quite a bit of money in this build so my loss is your gain. Please PM me your offer.
Installed Parts:
-Post upgrade p320 fcu
-Flux Raider Chassis
-Grey guns adjustable bronze trigger installed
-1911 guide rod with 15lb spring
-Effman upgraded safety striker spring
-Sig Guy p320 C.O.R.E kit. This replaces all of the questionable in quality SIG p320 firing parts. I kept the full strength sear springs to aid in safety.
-Zaffiri Full size threaded barrel
-Herrington Arms threaded comp
-Flux Gas pedel
-Ripstick charging handle
-Tyrant slide release
-Trijicon low RMR mount
-508T Holosun red dot optic
Belt:
-Large Grey Guns Gear belt
-Strike 80 kydex right hand RTI attachment level 2 holster with strap. This holster works with the Ripstick
-Belt pouches, mag pouches, medical pouch
-Monadnock asp with holder
Accessories and parts:
-Seven 21 round gen 2 mags SIG oem
-All the oem parts
-Hybrid Grey guns competition trigger(additional trigger so you can swap out the Grey Guns trigger if it’s not to your liking)
-Tyrant trigger(additional trigger so you can swap out the Grey Guns trigger if it’s not to your liking)
-Sig Guy spring kit
-Spare recoil springs
-Grey Guns recoil rod
-Kydex two mag belt holder
-Belt attachment for RTI holster
-Flux gas cap
-Flux stock
Trades I’m looking for:
-Fusion Firearms XP Pro Comp 9mm pistol with the prickle grip textured grip module.
-Holosun 508T red dot
-S&W 627 Lew Horton “hunter” 8 shot 6” revolver.
-Radian Ramjet for gen 5 g17(bronze barrel preferred)
-Surefire m600 or scout weapons light in black
-Aero M4E1 or better quality stripped lower reciever. I could also go for a cool looking good quality milled set.
-9mm ammo fmj cheap range ammo, 223/.556 cheap range ammo, 12 gauge 2 3/4in slugs, and 12 gauge mini shells. 9mm fmj range ammo.
-Champion 3500-4500 watt duel or tri fuel inverter generator with wheels(newish generator).
-Floor mounted drill press. Good quality press. I don’t need a commercial quality set up. Just a top notch home rig.
-Big fat $100 bills
This is very close to new. I’ve only fired around 100 rounds out of it. I did every upgrade that I could think of that would enhance the platform. You have to buy the entire kit. The only parts I’ll sell separately would be the additional triggers or the OEM barrel/recoil rod assembly. All of the parts, mags, and accessories are close to brand new. The only exception to that would be the ripstick and the chassis smoothing that performed. The Ripstick front sight was slightly scuffed during install so I touched it up with some enamel paint. The frame around the trigger well had a raised seam of plastic which I found uncomfortable. I sanded down just the surface and edges to an 800 grit surface just to remove this seam and smooth the sharp edges. It’s much more pleasurable to shoot. I checked with Flux before sanding/smoothing down the seam and sharp edges and they assured me it was fine to do so. See the below parts list and my trade list below. This is from my personal collection. I’m losing quite a bit of money in this build so my loss is your gain. Please PM me your offer.
Installed Parts:
-Post upgrade p320 fcu
-Flux Raider Chassis
-Grey guns adjustable bronze trigger installed
-1911 guide rod with 15lb spring
-Effman upgraded safety striker spring
-Sig Guy p320 C.O.R.E kit. This replaces all of the questionable in quality SIG p320 firing parts. I kept the full strength sear springs to aid in safety.
-Zaffiri Full size threaded barrel
-Herrington Arms threaded comp
-Flux Gas pedel
-Ripstick charging handle
-Tyrant slide release
-Trijicon low RMR mount
-508T Holosun red dot optic
Belt:
-Large Grey Guns Gear belt
-Strike 80 kydex right hand RTI attachment level 2 holster with strap. This holster works with the Ripstick
-Belt pouches, mag pouches, medical pouch
-Monadnock asp with holder
Accessories and parts:
-Seven 21 round gen 2 mags SIG oem
-All the oem parts
-Hybrid Grey guns competition trigger(additional trigger so you can swap out the Grey Guns trigger if it’s not to your liking)
-Tyrant trigger(additional trigger so you can swap out the Grey Guns trigger if it’s not to your liking)
-Sig Guy spring kit
-Spare recoil springs
-Grey Guns recoil rod
-Kydex two mag belt holder
-Belt attachment for RTI holster
-Flux gas cap
-Flux stock
Trades I’m looking for:
-Fusion Firearms XP Pro Comp 9mm pistol with the prickle grip textured grip module.
-Holosun 508T red dot
-S&W 627 Lew Horton “hunter” 8 shot 6” revolver.
-Radian Ramjet for gen 5 g17(bronze barrel preferred)
-Surefire m600 or scout weapons light in black
-Aero M4E1 or better quality stripped lower reciever. I could also go for a cool looking good quality milled set.
-9mm ammo fmj cheap range ammo, 223/.556 cheap range ammo, 12 gauge 2 3/4in slugs, and 12 gauge mini shells. 9mm fmj range ammo.
-Champion 3500-4500 watt duel or tri fuel inverter generator with wheels(newish generator).
-Floor mounted drill press. Good quality press. I don’t need a commercial quality set up. Just a top notch home rig.
-Big fat $100 bills
