This machine is in mint condition. I've only used it on thin, mild steel. It has a full bottle of 100% argon, multiple tungstens, torch accessories, and full packs of copper and aluminum filler rods. It has a foot pedal controller. You won't find a cleaner one without buying new. I have a crane...
Fs/Ft
3- 25 count box's
75 total disc
These will cut 1/2" SS sheets like butter and will not shatter
Best cutting wheels hands down
1 disc will cut 3-4 cars in half no issues
Never buy disc agian
May trade ?
$125 per 25 CT box
$375 for all 3 box's 75ct shipped
Insurance for shipping...
Up for sale is one vintage Simplex "W" 1 3/4 X 12 railroad/house jack in very good working order. Also, one vintage Simplex "K" 2 X 14 railroad/house jack in very good working order. Must pick up in or near Ellijay.
Got this to build the frame of my truck and now have no need for it since the truck frame never got started...used it once or twice to check square and then never touched it again...blade is still sharp as a razor and works amazing...cuts thru 2x4, 1/4" wall steel like butter...new these are...
Got a brand new Iwata LPH400 (1.6) with an extra clone for clear when i was going to paint my truck and have since lost all interest in both...gun is brand new in the box with a cup kit and the clone is new but missing the box for some reason...asking well under what i paid for them and anyone...
I have up for sale only a Mi-T-M portable kerosene forced air heater. Fires right up Works perfectly.
Factory Tested for Multiple Fuels built-in temperature control and sure start ignition
Kerosene · JP8/Jet A fuel · No. 1 or No. 2 fuel oil · No. 1 or No. 2 diesel fuel · Not approved for bio-fuel
Bought new by me around 4 months ago. 7 hours run time no heavy loads. Break in oil changed. I run Amsoil motor oil. New NGK plug. Never ran gas through it just propane and you can stick your nose in the tank to verify if you want. Too big for what I’m needing. Full brand new 30lb propane tank...
I have a like new champion 8500 watt inverter generator. Has 4 hours of run time on the clock. No issues, can start up and load test for you. Has 240 volt 30 amp twist lock and 2 120 volt 20 amp ports. Very quite running. Got it for my camper when boondocking. Decided to go a different route...
4 Ladders in all.
1 - Little Giant - used 250 lb.
2 - Werner (M1816) Ladders. -Used - one ladder is missing the base bar.
1- Used Extension Ladder. I think it is a Werner. 24-28 ft. Have not measured it.
I am no longer looking at roofs. Looking to meet close to me as I no longer drive and...
For sale I have a LNIB Matco compression tester (#CT110K) and a used MAC compression tester (#CT25).
The Matco tester I bought from a local tool truck around 2017-2018 when I was still turning wrenches for a living. I'm pretty sure I only used it once or twice.
The MAC tester I found in a...
For sale I have some used Snap-On and Blue-Point tools that I have duplicates of. Now that I'm not turning wrenches for a living anymore, I am looking to move these along to someone who can use them. I am good with most methods of payment.
3 piece Blue-Point 1/4" drive locking extensions - $75...
Hey all, for sale is a brand new Senco set (no box but never been used). Includes a Finishpro 35, Finishpro 15, and a SLS15. Tools are metal construction from a few years back so much higher quality than new production ones where they use lower quality internals. Includes a rolling bag. Not...