• ODT Gun Show & Swap Meet - May 4, 2024! - Click here for info

Search results for query: *

  1. Bobtail an aluminum frame 1911

    Oh yea forgot about that aspect of it. I may try and do it if I can't find anyone. I've been watching some good videos all day.

  2. Bobtail an aluminum frame 1911

    Looks great. Want to do mine?

  3. Bobtail an aluminum frame 1911

    I was really hoping someone would just be bored and do it for free. Just kidding. I would gladly pay. I've Gooden a few quotes and am fine with what they are asking, just wanted to see if I could find a shorter lead time.

  4. Bobtail an aluminum frame 1911

    I thought about doing that, but would rather just pay someone. The Springer will have to be refinished (cerakoated) so would rather have someone that has done it before do it and knock out the refinish as well.

  5. Bobtail an aluminum frame 1911

    I just picked up a Springfield LW Operator the other day and want to bobtail it. Anyone know of any places in the metro area that will do this? Also have a Kimber Pro Raptor that needs done as well. I've gotten a few quotes but the lead times are 2-3 months out. Any suggestions or info would be...

  6. 300 Blockout not Cycling

    Yea it sounds like something with the gas. I'd check the gas block and tube first then check the gas key on the bolt carrier as well to make sure it is properly staked.

  7. AR-15 safety

    This for sure. Along with takedown springs and detents. Those thing can fly through a room.

  8. AR-15 safety

    Too easy. Just take the grip off. Put a new detent and spring in and put grip back on. Will take all of about 60 seconds.

  9. AR-15 safety

    Should be. All it is is the selector, a spring and a pin. You just have to take the grip screw out to get to the spring. May have to take the trigger out as well if you have to remove the selector.
  10.

    How to get a bullet stuck in barrel out?

    Hammer and wooded dowel. Drill bit is not smart.
  11.

    ** Fort Daniel-barrel threading and other work **

    Looks good man. Good talking to ya while you were killing time.
  12.

    Need help on URX 3.1 rail installation

    Lawrenceville. Right at 20 and 316. Nate is a great guy and will most likely be able to take care of you.

  13. Best lower parts kit

    I usually buy just the parts I need and then buy upgraded parts for trigger and what not instead of buying a lpk for a mag catch, bolt catch, and buffer retainer.
  14.

    Need help with a jammed live round.

    I would put the top of the slide on a table and try to tap it loose. You could also stick a cleaning rod carefully down the barrel and see how far it goes to see if the round fired or not. If it did hit hard until it budges. If didn't well I am dumb and would probably still hit it hard until it...

  15. Duracoat/ ceracoat?

    Gotcha. Then yea don't know where to get cerakote locally, only the duracoat.

  16. Duracoat/ ceracoat?

    Elite Pawn in Conyers had the duracoat kits. I would go with the cerakote though. You can order it online or get one of the many places in Metro Atlanta to do it. Nate at Ft. Daniel did mine and he is awesome.

  17. What is your favorite oil, solvent?

    Frog lube is the shiznit.

  18. AR-15 Build Issue - Feedback Needed from ODT Brain Trust

    You could also get a set of the KNS pins. That is what I use with my Timney and it does the job. I don't even use the set screws.
  19.

    question about Case hardening/flame bluing

    On a small knife you can just take a torch to it to change the colors. It might mess up the heat treat though and change the hardness of the blade.
  20.

    Everyone remember This gun ?

    Like the burnt bronze. Thinking about doing a AR upper and lower in that same finish.
Back
Top Bottom