Search results for query: *

  1.

    My 300blk SBR CMMG will not fire

    It's a factory CMMG. The magazine catch has been a nuisance for a while but the gun always fired. Now it goes click on the cartridge. I always shoot it suppressed.
  2.

    My 300blk SBR CMMG will not fire

    I've always had trouble getting the magazine to catch. It easily catches when the upper is removed. Is the bolt in the way? My mechanical skills are poor. Now with a cartridge chambered I pull the trigger and all I hear is a click. I the bolt looks clean, I cleaned it again, without...
  3.

    M1A Gas System Reassembly Problem

    Thank you, my mind has left me these past months. And there wasn't much to leave at best.
  4.

    M1A Gas System Reassembly Problem

    I swapped out the plastic handguard for a walnut hand guard. I trimmed it some. Now I can not get the cylinder, piston and plug to seat. If I tilt the gun it slides up. Thank you all for sharing your knowledge. Frank.
  5.

    Colt 6940 Bolt Problem

    Thank’s everyone. Clean it off and guns blazing.....well, or sumthin.
  6.

    Colt 6940 Bolt Problem

    This is a hard crust on the bolt. Any ideas what it is, how it happened or how its fixed? Thank you
  7.

    Saiga Front Conversion. Gas tube not in alignment.

    I am converting my Saiga 5.45*39 so it can use AK hand guards. I bought a new gas tube and a bolt on lower hand guard retainer. I am using the handguards from an Arsenal. The bolt will not go all the way forward. It goes in only until it flares out from the unpainted portion. Am I to cut a...

  8. Anyone else been burned by "Hogleg Smith"?

    All things considered this is a significantly better outcome for you than I expected. I'd eat the $105 and move on. I've had nothing but bad luck lately with gunsmiths. I would gladly pay $105 for a mulligan. A few times. I'm in my Hell is other People mood.

  9. Reblued 17-2, ammo doesnt fit in chambers

    I have a S&W 17-2 that was hot blued. I took it to the range yesterday and a few of the chambers had too much blue and the bullets would not fit fully flushed. The cylinder would not rotate without forcing in the ammo. What should I use to remove the extra blue from the chamber with scratching...

  10. Need Re-Bluing Work Done

    http://davesgunsmithing.com/?page_id=9 I just dropped off a revolver with Dave for a hot blue. He had several high end engraved shot guns there for rebluing. Prices seemed very good, he has a nice shop and was great to deal with, give him a call.
  11.

    Bolt trouble with a Winchester 121D

    I added photos. That wire protruding in the 3rd and 4th photos looks like it shouldn't be sticking out, but I am not sure where it goes. I also don't know the correct position for the small lever held in place by the screw that the wire is wrapped around. Also there are two clips on the bolt...
  12.

    Bolt trouble with a Winchester 121D

    The firing pin may be pushed forward. I did need to remove a screw to remove the bolt and that may have been the cukprit. The bolt moves freely .
  13.

    Bolt trouble with a Winchester 121D

    I have a Winchester 121D that worked fine. Before I decided to take the stock and bolt off for a cleaning. Now that it's back together the bolt moves as it should but I did something and now it won't fire. The trigger moves smoothing back and forth but there is no click when I pull the trigger...
  14.

    Disassembling a 22/45. Gun won't fire. I can't remove the mainspring housing. Gun #2

    It's his dream and I don't think any of us want to know. My dreams generally involve augmented blondes.
  15.

    Disassembling a 22/45. Gun won't fire. I can't remove the mainspring housing. Gun #2

    It's now working. A SINCERE THANK YOU TO ALL. Lots of little nuances that need to be followed. Next time I will be more careful and closely follow the instructions. When is Glock gonna come out with a full sized 22LR with a TB dammit!!
  16.

    Disassembling a 22/45. Gun won't fire. I can't remove the mainspring housing. Gun #2

    I'm on YouPorn all the time and I've never seen a video on a 22/45. :) Thanks everyone, I will keep fiddling with it and try to find this site you refer to as Youtube. I do love the gun, I picked it over a 1911-22 or a M&P 22, the learning curve is a bit steeper than expected tho.
  17.

    Disassembling a 22/45. Gun won't fire. I can't remove the mainspring housing. Gun #2

    My 22/45 won't fire or dry fire. The gun worked fine until I cleaned it. I must have reassembled it incorrectly. Now I can pull out the lever, but the main spring housing won't swing out from the gun. The photo shows how far it will come out.
  18.

    S&W 36-1. Trigger does not cock hammer everytime (Problem gun #1)

    I took my new to me (and no longer for trade cuz it aint workin) 36-1 to Wilson Shoals today. Sometimes it fired, sometimes I pulled the trigger and the hammer didn't move, while the trigger stuck as shown in the photo. I fiddled with the hammer and it fired a few rounds then ceased working...

  19. Re-blueing with salts

    I can confirm my gun is now a black color. Hmm.
  20.

    My S&W 17-2 needs help

    I took it to Bartow today for a deep cleaning. BigTim says hello NWSharpshooter
Back
Top Bottom